In addition to this user guide, you can find help at these locations: Place on the wall with desired router position and mark screw locations. Place the wall-mount slots over the screws and slide the router down until the screws fit snugly into the wall-mount slots. Make sure the location is within reach of an electrical outlet. Make sure that the wall you use is smooth, flat, dry, and sturdy. Determine where you want to mount the router and which side you should use to mount it.Note- Linksys is not responsible for damages incurred by unsecured wall-mounting hardware. Two screws are needed to mount the router. The distance between the slots on the longer side is 210 mm. The distance between the slots on the short side is 104 mm. The router has wall-mount slots on the bottom of each foot for flexibility in mounting the router on the wall. (9) Power button (EU models only)-Press to turn on the router. (8) Power port-Connect the included AC power adapter. You can also restore the factory settings using Linksys Smart Wi-Fi on (7) Reset button-Press and hold for 10 seconds (until the power LED starts flashing) to reset the You can also connect a USB printer and share it across your network. (6) USB 2.0/eSATA combo port-Connect and share a USB or eSATA drive on your network or on the Internet. (5) USB 3.0 port-Connect and share a USB drive on your network or on the Internet. Note-For best performance, use CAT5e or higher rated cables on the Internet port. (4) Internet port-Connect an Ethernet cable to this yellow gigabit (10/100/1000) port, and to a broadband Internet cable/DSL or fiber modem. Note-For best performance, use CAT5e or higher rated cables on the Ethernet ports. (3) Ethernet ports-Connect Ethernet cables to these blue gigabit (10/100/1000) ports, and to wired devices on your network. (2) Wi-Fi Protected Setup™ button-Press to configure wireless security on Wi-Fi Protected Setup-enabled network devices. Note-For best performance, position the side antennas vertically as shown in the picture on the left. To connect the antennas, twist the antenna connector clockwise onto the antenna port on the router. (1) Adjustable antennas-This router ships with four adjustable external antennas that should be connected to the router before powering it on. The router supports one session at a time. Wait until the LED is off, and then try again. LED blinks amber if the Wi-Fi Protected Setup process fails. It will be solid white for five seconds to indicate a successful connection. (11) WPS Indicator-(White/Amber) The LED blinks slowly for up to two minutes during Wi-Fi A solid white LED indicates that the router is successfully connected to a device at 1000 Mbps. (10) ETHERNET 1 through 4 (Secondary)-(White) If the white LED is off, the router is successfully connected to a device through that port at 10/100 Mbps. A flashing white LED indicates network activity over that port. If the white LED is solid, the router is connected to a device through that port. (9) ETHERNET 1 through 4 (Primary)-(White) These numbered LEDs correspond with the numbered ports on the router’s back panel. A solid white LED indicates a USB 3.0 device is connected. (8) USB2 Secondary Indicator-(White) When off, a USB 1.0 or USB 2.0 device is connected. A blinking white indicates activity on the port. The LED is solid white when a USB device is connected. (7) USB2 Primary Indicator-(White) When off, the USB 3.0 port is off. A blinking white LED indicates activity on the port. (6) USB1 Indicator-(White) When off, the USB /eSATA port is off or an eSATA device isĬonnected. A blinking white LED indicates activity through the eSATA port. The LED is solid white when an eSATA device is connected. (5) eSATA Indicator-(White) When off, the USB/eSATA port is off or a USB device is connected. If the LED is blinking white, the router is sending or receiving data over the 5 GHz network. (4) 5 GHz Indicator-(White) The Wireless LED is solid white when one or more clients are connected to the 5GHz network. If the LED is blinking white, the router is sending or receiving data over the 2.4 GHz network. (3) 2.4 GHz Indicator-(White) The Wireless LED is solid white when one or more clients are connected to the 2.4 GHz network. Amber blinking indicates that the connection is down due to hardware issues. A solid amber LED indicates the connection is down due to configuration issues. It blinks white while the router works to establish a connection. (2) Internet Indicator-(White/Amber) The Internet LED is solid white when connected to the It will blink when the router goes through its self-diagnostic mode during every boot-up. (1) Power indicator-(White) The icon LED is solid white while the router is powered on.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |